According to the Euroturbo policy, the papers can be freely downloaded, once the authors have duly signed the permission to publish agreement form.
Terms and conditions for the use of the repository are available here.
- Assessement of numerical methods for low pressure turbine tone noise prediction
- On the modal sound field at the outlet of a turbocharger centrifugal compressor
- Separation control by acoustic excitation on highly loaded low pressure turbine blades
- Physics of vibrating low pressure turbine airfoils
- Loosely coupled fluid/solid heat transfer analysis using a dynamic HTC approach
- Performance improvement of a radial ORC turbine by means of automated CFD design
- Modelling of nuclear power plant steam turbines with simplifications
- Investigation of the roughness strip effects on the separation-induced transition with the γ- Re Θt transition model on a high-lift low-pressure turbine rotor blade at steady conditions
- Condensation of steam with chemical impurity in a turbine
- Numerical assessment of the noise emission of counter-rotating open rotors
- Thermodynamical and mechanical modelling analysis of high-speed turbomachine rotors
- CHT analyses of an industrial gas turbine blade: comparison between an in-house developed decoupled procedure and CFD coupled simulations
- Application of harmonic balance method to the simulation of unsteady rotor/stator interaction in the single stage
- Numerical investigation on the aerodynamics of a tunnel ventilation fan during pressure pulses
- Aircraft engine sensor fault detection, isolaton and reconfiguration using fuzzy logic control based unknown input observer
- Modelling rotor-rotor interaction on reduced passage counts using a time-domain Fourier approach
- Three-dimensional near wall flow phenomena of a tandem cascade
- Low weight, high speed automotive fan design by 3D inverse method
- HPC design based on multidisciplinary numerical simulation
- New stabilization methods of flows in plane, conic and annular diffusers
- Comparison of stationary internal cooling passage numerical simulations to experimental data
- Investigations of heat transfer and pressure loss in an engine-similar two-pass internal blade cooling configuration
- Numerical analyses of a cavitating Pelton Turbine
- Experimental analysis of the flow through the fan stage of a high-bypass turbofan in windmilling conditions
- Stationary internal cooling passage experiments for an engine realistic configuration
- Vortex development induced by part gap geometry and endwall configurations for variable stator vanes in a compressor cascade
- Quantification of the numerical solution sensitivity to tip clearance dimensions in an axial multistage compressor
- Temporal behavior of a boundary layer separation within a radial vaned diffuser
- Experimental investigations of endwall flow in a highly loaded annular compressor stator cascade
- Numerical simulation of a compressor facility test rig at near-surge operating conditions
- Film-cooling adiabatic effectiveness measurements on a real high pressure turbine blade
- Influence of the clearance size on rotating instability in an axial compressor stator
- Influence of vane carrier design in steam extraction modules on the flow conditions of the subsequent turbine stage
- Steam flow through a two-stage turbine with rotor drum arrangement
- Evolution of the aerodynamic stability of an oscillating annular compressor cascade with inlet reverse flow condition variations
- Impact of the large-scale environment on the tonal noise of axial fans
- Evaluation of unsteady CFD models applied to the analysis of a transonic HP turbine stage
- Small horizontal axis wind turbine: analytical blade design and comparison with RANS-predicted flow field and performance data
- Experimental investigation on the heat transfer in a turbine airfoil leading edge region: effects of the wedge angle and jet impingement geometries
- Heat transfer and friction in circular ducts with shaped ribs
- Study of the acoustic resonance occurring in a multistage highspeed axial compressor
- Numerical investigation on the influence of anisotropic surface structures on the skin friction
- Performance prediction and optimization of low pressure axial fans by artificial neural networks
- High-order discontinuous Galerkin solution of the RANS and explicit algebraic Reynolds stress Κ–Ω equations in turbomachinery flows
- Design of the primary liquid-metal pump of the Myrrha research reactor
- Three-dimensional gusts for the prediction of tonal fan noise
- High-speed aerodynamic investigation of the midsection of a 48″ rotor blade for the last stage of steam turbine
- Low speed numerical and experimental validation of a solving methodology for the inverse heat conduction problem by means of quantitative infra-red thermography
- Influence of regeneration-induced variances of stator vanes on the vibration behaviour of rotor blades in axial turbines
- A Comparative study of RANS, URANS and NLES approaches for flow prediction in pin fin array
- Unsteady wall pressure measurement in an one-and-a-half stage axial transonic compressor during stall inception
- Modelling unsteadinesses and polydispersion in wet steam flows using the quadrature method of moments and a two-equation model
- Sensitivity and uncertainty of the radial mode analysis for turbomachinery applications
- Model-based control and diagnostic techniques for operational improvements of gas turbine engines
- Description of the unsteady flow pattern from peak efficiency to near surge in a subsonic centrifugal compressor stage
- New double-shaft compressor for two-shaft combined cycle power units and prospects of their application
- Potential of power recovery of an axial fan in windmilling operation
- Experimental comparison between a counter-rotating axial-flow fan and a conventional rotor-stator stage
- The unsteady low-frequency aerodynamic forces acting on rotor blades in the first two stages of a jet engine axial compressor in the case of a bird strike
- Simulation of near surge instabilities onset in a turbocharger compressor
- Experimental and numerical investigations to extend the validity range of a turbine loss correlation for ultra-low aspect ratios in transonic flow
- Aerodynamic design studies of a transonic centrifugal compressor impeller based on automated 3D-CFD optimization
- Optimization and validation of trailing edge blowing for the reduction of rotor-stator interaction noise
- Study of the aerodynamic instabilities in an axial flow compressor using 3D-1D codes coupling approach
- Steady CFD simulations of trailing edge film cooling in a linear nozzle vane cascade
- An advanced axial-slot casing treatment on a tip-critical transonic compressor rotor Part 1: Unsteady hot wire and wall pressure measurements
- An advanced axial-slot casing treatment on a tip-critical transonic compressor rotor Part 2: Taking a closer look with CFD
- Enhanced loss prediction for admission through circumferential slots in axial steam turbines
- Experimental aeroelastic investigation of vibrating turbine blade clusters
- The tip clearance effects on the centrifugal compressor vaneless diffuser flow fields at off-design conditions
- Circumferential grooves for a modern transonic compressor: Aerodynamic effects, benefits and limitations
- Predicted performance of brush seals: Porous medium versus resolved bristle matrix and comparison with experimental data
- The effects of Reynolds number and roughness on compressor performance
- Numerical simulations of Small Turbodrill performance
- Control of secondary flow structures on a highly loaded compressor cascade
- Performance testing of a low-pressure compressor
- Application of a new numerical solver to turbomachinery flow problems
- Unsteady velocity PIV measurements and 3D numerical calculation comparisons inside the impeller of a radial pump model
- A numerical comparison on the aerodynamic performances of a two-stage two-spool turbine facility predicted by steady and unsteady simulations
- A generic steam turbine exhaust diffuser with tip leakage modelling and non-uniform hood outlet
- Review and collection of preliminary design rules for low solidity diffusers
- Study on the effects of axial clearance size on the operation of an axial flow electric motor cooling fan
- Automated optimization of the non-axisymmetric hub endwall of the rotor of an axial compressor
- TurboSphere - Multistage micro turbine for secondary energy sources recovery
- On the interaction of streamwise vorticity with a rotating turbine blade
- Experimental investigation of unsteadiness associated with film cooling flow ejection from the vane pressure side
- Application of thermochromic liquid crystal mixtures for transient heat transfer measurements
- Shroud contour optimization for a turbocharger centrifugal compressor trim family
- Semi automated improvement of wind blade design
- Numerical analysis of compressor blade flutter in modern gas turbine engines
- Adjoint optimisation of a high pressure turbine stage for a lean-burn combustion system
- Experimental study of the effects of temperature variation on droplet size and wetness fraction in a low pressure model steam turbine
- The design of ultra-high-speed miniature centrifugal compressors
- Two-fluid model for prediction of wet steam flow